Programmer [CH341A] USB to serial port
A must-have tool, version of the CH341A programmer. It is fully compatible with the market version.
[A group label MEM] 24Cxx, 25Qxx programming
[B group label UART] USB to UART, ISP
The two groups of functions are switched through the MODE switch . The 5V/3V3 power supply can be switched through the POWER switch (acting on all pin headers and locking seats marked with VDD on the board ), and at the same time it can provide two voltage outputs (5V and 3V3 pin headers under the switch).
Programmer [CH341A] USB to serial port ver.2.3
Programmer [CH341A] USB to serial port
*PCBWay community is a sharing platform. We are not responsible for any design issues and parameter issues (board thickness, surface finish, etc.) you choose.
- Comments(5)
- Likes(6)
- peter.babic May 01,2023
- Engineer Feb 02,2023
- tripleclown Nov 10,2022
- Voloschuk Igor Dec 11,2020
- Engineer Sep 11,2020
- rachman bobo Sep 10,2020
- 3 USER VOTES
- YOUR VOTE 0.00 0.00
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
-
10design
-
10usability
-
10creativity
-
10content
-
9design
-
8usability
-
10creativity
-
8content
-
10design
-
10usability
-
10creativity
-
10content
More by Oleg Oleg
- Development Board STM32F103RET6 Development Board Series STM32F103RET6Resources on the board3.3/5.0/12V power input/output pinReset ...
- DAPLINK and STM32 minimum system combination DAPLINK and STM32 minimum system combination, one data cable can complete the download and debugging...
- USB to RS232 This is a program verification board. The main verification content is the function of USB to RS232 ...
- ESP Air Burner The ESP downloader with Air Burnner interface uses probes instead of DuPont cables.
- Docking station USB3.1 Using GL3520 USB 3.1 HUB chip,Supports super high speed, high speed and full speed USB connection, f...
- RX5808 open source receiver 5.8g open source receiver, can receive 5.8g signal, AV video signal output. Rx5808 dual-reception fu...
- 5.8G image transmission module It can be used for AV signal audio and video wireless transmission; baby monitor; wireless camera se...
- GRBL-ESP32 esp32s 3d is suitable for GRBL and marlin software
- STM32 Sensor Node A Small STM32F103C8T6 board with all functional pins exposed. Similar to the BluePill Board except:N...
- 2.8 inch TFT touch screen The module uses a 2.8-inch TFT color LCD screen. The module is compatible with punctual atomic 2.8TF...
- LED dot matrix clock LED dot matrix electronic clock based on 51 single chip microcomputer.Based on STC15W4K series ultra...
- STM32F411Cx 401Cx minimum system + J-LINK debugger The STM32F411 / 401 microcontroller belongs to the STM32 Dynamic Efficiency series. These devices ar...
- Small passive DC constant current electronic load IntroductionA small passive DC adjustable constant current (CC) electronic load with temperature-con...
- Small jlinkV9 downloader V1.0 Adopt typec interface, stm32f205 master control, lead SWD, SWO, support virtual serial port, resista...
- IP2325 dual string lithium battery charging module Miniature charger for dual lithium batteries.Since the IP2325 does not have a charge balancing funct...
- Electronic switch The operating voltage is within 30V. Depends on the PMOS voltage.
- Power supply module NAE20S08 Is based on SY8288A / JW5068A series power supply ic Volume: 10x10x6mm Input range: 4-23vin Output: ...
- Solder paste dispenser A portable miniature intelligent electric SMT solder paste dispensing pen supports quantitative extr...
-
-
-
DIY Transistor Tester | Build Your Own LCR Meter at Home with Arduino Nano
121 0 0 -
-
-
ESP32-S3 breakout board for motorizing Iron Man helmets
170 0 2 -
Build a Walking Robot: Theo Jansen Style 3D Printed Octopod
266 0 5 -
-